ADG739BRU-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 100μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG739 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | AUDIO/VIDEO SWITCH |
| Operating Supply Current | 10μA |
| Power Dissipation | 100μW |
| Max Supply Current | 20μA |
| Throw Configuration | 4PST |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Supply Type | Single |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF 42pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 20ns, 10ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -75dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Voltage - Supply, Single (V+) | 2.7V~5.5V |
| Signal Current-Max | 0.01A |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG739BRU-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 4:1. Increasing operating temperature to around -40°C~85°C TA. In total, 16 terminations have occurred. The electronic part provides high-quality output because it has 4 channels. A 3V voltage supply should turn on and run the electronic component. As part of the design of the 16 series, this electronic part has been incorporated into the system. Multiplexers built on a SP4T switching circuit are built. It consists of 2 circuits. Try searching with ADG739 to find analog multiplexer variants. As far as internal resistance is concerned, it has 4.5Ohm. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analog switch ics with Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2.7V. For this digital switch to work, 10μA current would suffice. Using a single voltage supply, this switch device consumes 2.7V~5.5V volts. A voltage higher than 20μA may cause damage to the switch multiplexer. It is integrated with a AUDIO/VIDEO SWITCH analog IC. It is possible to operate 8 inputs.
ADG739BRU-REEL7 Features
4 Channels
Switch Circuit: SP4T
10μA Supply Current
-3db Bandwidth: 100MHz
ADG739BRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG739BRU-REEL7 Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Multiplexers
- Frame Relay Equipment
- Precision data acquisition
- MP3 players
- Sample-and-hold systems
- Imaging
- Residential Gateways, Home Gateway/Router
- SONET
- Communication systems
