ADG741BKSZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Additional Feature | CAN ALSO OPERATE WITH 5 VOLT SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG741 |
| Pin Count | 6 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 3Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Height | 1mm |
| Length | 2.2mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG741BKSZ-REEL7 Overview
The electronic component is convenient to ship overseas because it is packed in a 6-TSSOP, SC-88, SOT-363. High reliability is provided by advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 6. This electronic part offers high-quality output due to its 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 6 series, this electronic part has been incorporated into the system. Multiplexers built on a SPST - NO switching circuit are built. Try searching for the analog switch ic with ADG741 if you are looking for variants. There is 3Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 6 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. It is recommended to use 1.8V as the lowest voltage for the electrical part. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. The analogue multiplexer may be damaged if voltage is greater than 1μA. 200MHz bandwidths enable data to be transferred. Check out the electrical component's additional features, such as the following: CAN ALSO OPERATE WITH 5 VOLT SUPPLY.
ADG741BKSZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 VOLT SUPPLY
ADG741BKSZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG741BKSZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Medical
- USB 1.1 signal switching circuits
- ATM
- Communication systems
- DSUs
- Low-Voltage
- PDAs
- Communications systems
- Mechanical reed relay replacement
- Switching Systems
