ADG742BKSZ-REEL
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | CAN ALSO OPERATE WITH 5 VOLT SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG742 |
| Pin Count | 6 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG742BKSZ-REEL Overview
Shipping overseas is convenient with the electronic component packed in 6-TSSOP, SC-88, SOT-363. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Temperatures around -40°C~85°C TA are extended for operation. In total, there have been 6 terminations. By its 1 channels, the electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. It is part of the design of the 6 series that this electronic component is included. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching with ADG742 if you're looking for variants. An switch multiplexer with 3Ohm internal resistance has a value of 3Ohm. The functions of 6 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. In order for the electronic part to function properly, the lowest voltage should be 1.8V. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. It may damage the digital multiplexer if the voltage is higher than 1μA. Don't forget the additional features of this electronic part, such as: CAN ALSO OPERATE WITH 5 VOLT SUPPLY.
ADG742BKSZ-REEL Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE WITH 5 VOLT SUPPLY
ADG742BKSZ-REEL Applications
There are a lot of Analog Devices Inc. ADG742BKSZ-REEL Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Video switching
- ISDN NT1/TA
- Residential Gateways, Home Gateway/Router
- Battery Powered Instruments
- Isolation
- E1 Network Equipment
- PBXs
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Audio signal routing
