Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
12-WFQFN Exposed Pad, CSP |
Surface Mount |
YES |
Number of Pins |
12 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
12 |
ECCN Code |
EAR99 |
Resistance |
6.7Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
QUAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3.3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG772 |
Pin Count |
12 |
Number of Outputs |
4 |
Operating Supply Voltage |
3.6V |
Power Supplies |
3/3.3V |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
2.7V |
Test Frequency |
1MHz |
Power Dissipation |
21.6nW |
Max Supply Current |
6nA |
Turn On Delay Time |
9 ns |
Number of Inputs |
2 |
Bandwidth |
630MHz |
Turn-Off Delay Time |
6 ns |
On-State Resistance (Max) |
6.7Ohm Typ |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
73 dB |
Current - Leakage (IS(off)) (Max) |
200pA |
Channel Capacitance (CS(off), CD(off)) |
2.4pF 6.9pF |
On-state Resistance Match-Nom |
0.04Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
12.5ns, 9.5ns |
Charge Injection |
0.5pC |
Channel-to-Channel Matching (ΔRon) |
40m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
9.5ns |
Voltage - Supply, Single (V+) |
2.7V~3.6V |
Height Seated (Max) |
1mm |
Length |
3mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG772BCPZ-1REEL Overview
The electronic component is convenient to ship overseas because it is packed in a 12-WFQFN Exposed Pad, CSP. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Extended operating temperature around -40°C~85°C TA. A total of 12 terminations have been recorded. A 1 channel electronic part produces high-quality output. With a 3.3V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 12 pins. Circuits based on SPDT switching are used to construct these analog switch ics. Use ADG772 to search for variants of the digital switches. It has an internal resistance of 6.7Ohm. For details about the functions of 12 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 3.6V to a switch device. 2.7V should be the lowest voltage fed to the electronic component. Using only a single voltage supply, this analog switch requires 2.7V~3.6V voltage. A digital multiplexer may suffer damage if voltage is applied above 6nA. 3.6V operating voltages are supported by the electronic component. A 2 input needs to be operated. There are various bandwidths available for data transfer. An output of 4 is provided by the digital multiplexer.
ADG772BCPZ-1REEL Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 630MHz
ADG772BCPZ-1REEL Applications
There are a lot of Analog Devices Inc. ADG772BCPZ-1REEL Analog Switches & Multiplexers ICs applications.
- FTTH
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cellular phones
- Battery-powered systems
- Relay replacements
- ATM
- Channel Banks
- Cable PC
- Communication systems
- Access Concentrators