ADG774ABCPZ-R2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN Exposed Pad, CSP |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Digi-Reel® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 3.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ALSO OPERATES WITH SUPPLY VOLTAGE 5V |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG774 |
| Pin Count | 16 |
| Number of Channels | 2 |
| Interface | Parallel |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 0V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Number of Inputs | 8 |
| Bandwidth | 400MHz |
| On-State Resistance (Max) | 3.5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 7.5pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 12ns, 6ns |
| Charge Injection | 6pC |
| Channel-to-Channel Matching (ΔRon) | 150m Ω |
| Crosstalk | -70dB @ 10MHz |
| Voltage - Supply, Single (V+) | 3V~5V |
| Signal Current-Max | 0.1A |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG774ABCPZ-R2 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-WFQFN Exposed Pad, CSP. Advanced packaging method Digi-Reel? is used to provide high reliability. This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 2 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Circuits based on SPDT switching are used to construct these analog switch ics. Circuits number 4 make up this analogue multiplexer. Try searching with ADG774 to find analog multiplexer variants. Analog switches have 3.5Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. In order for the electronic part to function properly, the lowest voltage should be 0V. Analogue multiplexers require a 3V~5V voltage to drain from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. Operating the 8 inputs requires 8 inputs. 400MHz bandwidths enable data to be transferred. This electronic part has additional features, such as: ALSO OPERATES WITH SUPPLY VOLTAGE 5V.
ADG774ABCPZ-R2 Features
2 Channels
Switch Circuit: SPDT
Bandwidth: 400MHz
Additional Features: ALSO OPERATES WITH SUPPLY VOLTAGE 5V
ADG774ABCPZ-R2 Applications
There are a lot of Analog Devices Inc. ADG774ABCPZ-R2 Analog Switches & Multiplexers ICs applications.
- DVD-R
- DSLAMs
- Precision instrumentation
- PBX interfaces
- Routers
- Avionics
- Cable Modem
- Precision test equipment
- Avionics test equipment
- ATM
