Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 4 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
3.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
3V |
Terminal Pitch |
0.635mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG774 |
Pin Count |
16 |
Power Supplies |
3/5V |
Number of Channels |
2 |
Interface |
Parallel |
Number of Circuits |
4 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
0V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Throw Configuration |
DPST |
Number of Inputs |
8 |
Bandwidth |
400MHz |
On-State Resistance (Max) |
3.5Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 7.5pF |
On-state Resistance Match-Nom |
0.15Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
12ns, 6ns |
Charge Injection |
6pC |
Channel-to-Channel Matching (ΔRon) |
150m Ω |
Crosstalk |
-70dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
3V~5V |
Height |
1.65mm |
Length |
4.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG774ABRQZ Overview
Presented in 16-SSOP (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. There is 2:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 2 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. An electrical component of this type can be found in the 16 series. SPDT switching circuits are used in these analog switch ics. 4 circuits are used in this analogue multiplexer. Try searching with ADG774 if you're looking for variants. The internal resistance of this digital multiplexer is 3.5Ohm. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. In order for the electronic part to function properly, the lowest voltage should be 0V. An analogue multiplexer drains from a single voltage supply at 3V~5V. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. Among the inputs that can be operated are the 8 inputs. A 400MHz-bandwidth can be used for data transfer.
ADG774ABRQZ Features
2 Channels
Switch Circuit: SPDT
Bandwidth: 400MHz
ADG774ABRQZ Applications
There are a lot of Analog Devices Inc. ADG774ABRQZ Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- HDTV
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Instruments
- Ultrasound
- DSUs
- Digital cross connects (DSX-1)
- Sample-and-hold systems
- Digital Cross-Connects
- Relay Replacement