ADG779BKSZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 5Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG779 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 14 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 3 ns |
| On-State Resistance (Max) | 5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 14ns, 3ns (Typ) |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 7ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG779BKSZ-REEL Overview
The electronic part can be shipped overseas conveniently because it is packaged in 6-TSSOP, SC-88, SOT-363. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. The total number of terminations is 6. A electrical component with 1 channels is capable of high-quality output. A 3V voltage supply should turn on and run the electronic component. A key feature of the 6 series is the inclusion of this electronic part as part of its design. A SPDT switching circuit is used for these analog switches. Try searching for the analog switch ic with ADG779 if you are looking for variants. The internal resistance of this digital multiplexer is 5Ohm. To find out what the functions of 6 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. It is recommended that the electrical component receives a voltage of 1.8V. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA. It is possible to transfer data over a 200MHz-bandwidth. Multiplexer ics with 2 outputs are available.
ADG779BKSZ-REEL Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 200MHz
ADG779BKSZ-REEL Applications
There are a lot of Analog Devices Inc. ADG779BKSZ-REEL Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Audio and video signal routing
- Audio signal routing
- RGB switches
- Automatic test equipment
- Industrial and process control systems
- PCMCIA cards
- PBX interfaces
- Fiber In The Loop (FITL)
- Transmit
