ADG781BCPZ
| Parameters | |
|---|---|
| Crosstalk | -90dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 12ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 750μm |
| Length | 4.1mm |
| Width | 4.1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-WFQFN Exposed Pad, CSP |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tray |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Additional Feature | CAN ALSO OPERATE AT 5V NOMINAL |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG781 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 11 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 6 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 11ns, 6ns (Typ) |
| Charge Injection | 3pC |
ADG781BCPZ Overview
Presented in 20-WFQFN Exposed Pad, CSP, this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tray is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. There are 20 terminations totally. A electrical component with 4 channels is capable of high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. It is part of the design of the 20 series that this electronic component is included. These analog multiplexers are built based on SPST - NC switching circuits. If you are looking for variants of the digital switch, trying search with ADG781. This digital multiplexer has 4Ohm internal resistance. The functions of 20 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. The lowest voltage the electronic part should receive is 1.8V. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. The data can be transferred over a wide range of bandwidths, called 200MHz bandwidths. Don’t miss additional features of the electronic component such as: CAN ALSO OPERATE AT 5V NOMINAL.
ADG781BCPZ Features
4 Channels
Switch Circuit: SPST - NC
Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE AT 5V NOMINAL
ADG781BCPZ Applications
There are a lot of Analog Devices Inc. ADG781BCPZ Analog Switches & Multiplexers ICs applications.
- CSU
- High reliability control systems
- SDH/SONET multiplexers
- DSLAMs
- Low-Voltage
- Audio signal routing
- Cellular phones
- Sample hold systems
- Residential Gateways, Home Gateway/Router
- Industrial and process control systems
