ADG782BCPZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-WFQFN Exposed Pad, CSP |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG782 |
| Pin Count | 20 |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 11 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 6 ns |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 11ns, 6ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 10MHz |
| Switch-off Time-Max | 12ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG782BCPZ-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 20-WFQFN Exposed Pad, CSP. The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Extended operating temperature around -40°C~85°C TA. There are 20 terminations totally. By its 4 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. There is an electrical component included in the 20 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. Use ADG782 to search for variants of the digital switches. This digital multiplexer has 4Ohm internal resistance. To find out what the 20 pins do, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. The lowest voltage the electronic part should receive is 1.8V. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. There are various bandwidths available for data transfer.
ADG782BCPZ-REEL7 Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
ADG782BCPZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG782BCPZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- Fiber to the Home
- Signal routing between systems
- Digital cross connects (DSX-1)
- Industrial and process control systems
- Cable Modem
- MP3 players
- Medical systems
- Fault Tolerant Systems
- DSUs
