ADG783BCPZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-WFQFN Exposed Pad, CSP |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tray |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | CAN ALSO OPERATE AT 5V NOMINAL |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG783 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 11 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 6 ns |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 11ns, 6ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 10MHz |
| Switch-off Time-Max | 12ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 830μm |
| Length | 4mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG783BCPZ Overview
The electrical component comes in 20-WFQFN Exposed Pad, CSP packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tray. In Surface Mount, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 20 terminations. The electronic part delivers high-quality output through its 4 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. There is an electrical component included in the 20 series. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. Using the ADG783 search parameter, you can discover variants of the switch. This digital multiplexer has 4Ohm internal resistance. You can find the functions of the 20 pins in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. A low voltage of 1.8V should be applied to the electronic component. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. This switch operates within the bandwidth of 200MHz. Check out the electrical component's additional features, such as the following: CAN ALSO OPERATE AT 5V NOMINAL.
ADG783BCPZ Features
4 Channels
Switch Circuit: SPST - NO/NC
Bandwidth: 200MHz
Additional Features: CAN ALSO OPERATE AT 5V NOMINAL
ADG783BCPZ Applications
There are a lot of Analog Devices Inc. ADG783BCPZ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- SDH
- T1/E1 Terminals
- Digital cross connects (DSX-1)
- Switching Systems
- Low-Voltage
- Multi-Line E1 Interface Cards
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Automatic test equipment
- CSU
