ADG787BCBZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFBGA, WLCSP |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -20°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Max Power Dissipation | 5.5μW |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG787 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Test Frequency | 1MHz |
| Power Dissipation | 5.5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 13 ns |
| Number of Inputs | 2 |
| Bandwidth | 145MHz |
| Turn-Off Delay Time | 3 ns |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 63 dB |
| Current - Leakage (IS(off)) (Max) | 50pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 16pF |
| On-state Resistance Match-Nom | 0.07Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 19ns, 5ns |
| Insertion Loss (dB) | 0.2 dB |
| Charge Injection | 14pC |
| Channel-to-Channel Matching (ΔRon) | 20m Ω |
| Crosstalk | -110dB @ 1MHz |
| Switch-on Time-Max | 35ns |
| Switch-off Time-Max | 7ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.63mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG787BCBZ-REEL7 Overview
Presented in 10-UFBGA, WLCSP, this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -20°C~85°C TA. Total terminations are 10. High-quality output is provided by the electronic component's 1 channels. An 2.7V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 10 series of products. On the other hand, analog switches can be constructed using SPDT switching circuits. Look for analog switch ic variants by searching with ADG787. The internal resistance of this digital multiplexer is 3Ohm. Please refer to the datasheets for 10 pins functions. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. 1.8V should be the lowest voltage fed to the electronic component. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. A voltage of 5.5V can be used to operate the electronic component. Operating 2 inputs is required. In 145MHz-bandwidths, data can be transferred. The analogue multiplexer has 4 outputs.
ADG787BCBZ-REEL7 Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 145MHz
ADG787BCBZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG787BCBZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Video switching
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- HDTV
- DSUs
- New designs requiring multiplexer functions
- Relay Replacement
- Cellular phones
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Medical Instrumentation
- Automatic test equipment
