Parameters |
Polarity |
Non-Inverting |
Power Supplies |
2/5V |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1nA |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
45 ns |
Supply Type |
Single |
Bandwidth |
12MHz |
Turn-Off Delay Time |
15 ns |
On-State Resistance (Max) |
300mOhm |
High Level Output Current |
400mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
61 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
180pF 180pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
45ns, 15ns |
Charge Injection |
50pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
55ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Normal Position |
NO |
Height |
850μm |
Length |
3mm |
Width |
3mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
300mOhm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG801 |
Pin Count |
8 |
Qualification Status |
Not Qualified |
ADG801BRM Overview
The electrical component comes in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tube. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~125°C TA. Total terminations are 8. A electrical component with 1 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. 8 pins are injected to the electronic part body. These analog multiplexers are built based on SPST - NO switching circuits. Try searching for the analog switch ic with ADG801 if you are looking for variants. As far as internal resistance is concerned, it has 300mOhm. To find out what the functions of 8 pins are, please refer to their datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 1.8V. 1nA current would be enough for this multiplexer to operate. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. A voltage higher than 1μA may cause damage to the switch multiplexer. 12MHz-bandwidths can be used to transfer data between multiplexers.
ADG801BRM Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Bandwidth: 12MHz
ADG801BRM Applications
There are a lot of Analog Devices Inc. ADG801BRM Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- High speed data transmission line cards
- Medical Instrumentation
- Imaging
- Fiber to the Home
- Precision instrumentation
- PDAs
- T1/E1 Terminals
- Private Branch Exchange (PBX)
- Routers