ADG801BRM-REEL7
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG801 |
| Pin Count | 8 |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| -3db Bandwidth | 12MHz |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
ADG801BRM-REEL7 Overview
Presented in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), this electrical component is convenient for overseas shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around -40°C~125°C TA are extended for operation. In total, there are 8 terminations. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPST - NO switching circuits. ADG801 can be used to search for analog multiplexer variants. A 300mOhm internal resistance characterizes this multiplexer. Please refer to the datasheets for 8 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Single supply type digital switch with a low cost. 1.8V should be the lowest voltage fed to the electronic component. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. When the digital multiplexer is charged above 1μA, damage can occur.
ADG801BRM-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 12MHz
ADG801BRM-REEL7 Applications
There are a lot of Analog Devices Inc. ADG801BRM-REEL7 Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- Communication systems
- E1 Network Equipment
- Wireless Local Loop
- Microprocessor controlled systems
- Precision test equipment
- SONET/SDH ADM
- Communications systems
- Mechanical reed relay replacement
- HDTV
