Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
300mOhm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG801 |
Pin Count |
8 |
Polarity |
Non-Inverting |
Power Supplies |
3/5V |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1nA |
Nominal Supply Current |
1μA |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
45 ns |
Supply Type |
Single |
Bandwidth |
12MHz |
Turn-Off Delay Time |
15 ns |
On-State Resistance (Max) |
300mOhm |
High Level Output Current |
400mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
61 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
180pF 180pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
45ns, 15ns |
Charge Injection |
50pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
55ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Normal Position |
NO |
Height |
850μm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG801BRMZ Overview
This electronic part is conveniently packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tube is used. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~125°C TA is the extended operating temperature. The total number of terminations is 8. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. The electrical component body receives 8 pins. The analog switch ics are built using SPST - NO switching circuits. Look for analog switch ic variants by searching with ADG801. An switch multiplexer with 300mOhm internal resistance has a value of 300mOhm. Please refer to the datasheets for 8 pins functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 1.8V. This digital switch can be operated with a current of 1nA. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. 12MHz bandwidths enable data to be transferred.
ADG801BRMZ Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Bandwidth: 12MHz
ADG801BRMZ Applications
There are a lot of Analog Devices Inc. ADG801BRMZ Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- Audio and video signal routing
- Video switching
- Channelized and Unchannelized DS3 applications
- Industrial
- MP3 players
- Audio signal routing
- Battery Powered Systems
- Fiber In The Loop (FITL)
- Microprocessor controlled systems