banner_page

ADG801BRT-500RL7

45ns, 15ns SPST - NO 300mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG801 6 Pins 250pA 3V SOT-23-6


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-ADG801BRT-500RL7
  • Package: SOT-23-6
  • Datasheet: PDF
  • Stock: 123
  • Description: 45ns, 15ns SPST - NO 300mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG801 6 Pins 250pA 3V SOT-23-6(Kg)

Details

Tags

Parameters
Resistance 300mOhm
Subcategory Multiplexer or Switches
Max Power Dissipation 5μW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 240
Number of Functions 1
Supply Voltage 3V
Terminal Pitch 0.95mm
Reach Compliance Code not_compliant
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number ADG801
Pin Count 6
Qualification Status Not Qualified
Power Supplies 3/5V
Number of Channels 1
Interface Parallel
Max Supply Voltage 5.5V
Min Supply Voltage 1.8V
Operating Supply Current 1nA
Nominal Supply Current 1nA
Power Dissipation 5μW
Max Supply Current 1μA
Throw Configuration SPST
Turn On Delay Time 45 ns
Supply Type Single
Bandwidth 12MHz
Turn-Off Delay Time 15 ns
On-State Resistance (Max) 300mOhm
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 61 dB
Current - Leakage (IS(off)) (Max) 250pA
Channel Capacitance (CS(off), CD(off)) 180pF 180pF
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 45ns, 15ns
Charge Injection 50pC
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 55ns
Voltage - Supply, Single (V+) 1.8V~5.5V
Max Junction Temperature (Tj) 150°C
Normal Position NO
On-State Resistance 250mOhm
Height 1.45mm
Length 2.9mm
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead
Mounting Type Surface Mount
Package / Case SOT-23-6
Surface Mount YES
Number of Pins 6
Operating Temperature -40°C~125°C TA
Packaging Tape & Reel (TR)
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 6
ECCN Code EAR99

ADG801BRT-500RL7 Overview


The electronic component is convenient to ship overseas because it is packed in a SOT-23-6. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. There are 6 terminations totally. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. 6 pins are injected to the electronic part body. SPST - NO switching circuits are used in these analog switch ics. Try searching with ADG801 if you're looking for variants. This digital multiplexer has 300mOhm internal resistance. You can find the functions of the 6 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 5.5V. An effective Single supply digital multiplexer. There should be 1.8V voltage fed to the electrical part below 1.8V. The analogue multiplexer could operate on 1nA current. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. The data can be transferred over a wide range of bandwidths, called 12MHz bandwidths.

ADG801BRT-500RL7 Features


1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Bandwidth: 12MHz

ADG801BRT-500RL7 Applications


There are a lot of Analog Devices Inc. ADG801BRT-500RL7 Analog Switches & Multiplexers ICs applications.

  • Battery-powered systems
  • Automotive applications
  • DSUs
  • E1 Multiplexer
  • Signal routing between systems
  • SONET/SDH ADM
  • Medical Instrumentation
  • FTTH
  • High speed data transmission line cards
  • Imaging

Write a review

Note: HTML is not translated!
    Bad           Good