ADG801BRT-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG801 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 12MHz |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Length | 2.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG801BRT-REEL7 Overview
Shipping overseas is convenient due to the electrical component's packing in SOT-23-6. High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~125°C TA. 6 terminations have been made so far. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. A total of 6 pins are injected into the body of the electronic part. The analog switch ics are built using SPST - NO switching circuits. Use ADG801 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 300mOhm. You can find the functions of the 6 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 5.5V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 1.8V. 1nA current would be enough for this multiplexer to operate. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. There are various bandwidths available for data transfer.
ADG801BRT-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Bandwidth: 12MHz
ADG801BRT-REEL7 Applications
There are a lot of Analog Devices Inc. ADG801BRT-REEL7 Analog Switches & Multiplexers ICs applications.
- DSLAMs
- HDTV
- SONET
- Routers
- Remote Powered Equipment
- E1 Network Equipment
- PCMCIA cards
- Avionics test equipment
- Digital access cross connects
- Microprocessor controlled systems
