ADG802BRM
| Parameters | |
|---|---|
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG802 |
| Pin Count | 8 |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| -3db Bandwidth | 12MHz |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
ADG802BRM Overview
Packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~125°C TA is the extended operating temperature. In total, 8 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPST - NC switching circuits. Try searching for ADG802 variants of the analog switch ic. In this multiplexer, the internal resistance is 300mOhm. To find out what the functions of 8 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. A cost-effective Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 1.8V. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA.
ADG802BRM Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 12MHz
ADG802BRM Applications
There are a lot of Analog Devices Inc. ADG802BRM Analog Switches & Multiplexers ICs applications.
- ATM
- Cellular phones
- Modems
- Signal routing between systems
- Intelligent PBX
- Multi-Line E1 Interface Cards
- High speed data transmission line cards
- Medical Instrumentation
- Fiber In The Loop (FITL)
- Cross Connects
