ADG802BRM-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG802 |
| Pin Count | 8 |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| -3db Bandwidth | 12MHz |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG802BRM-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~125°C TA is the extended operating temperature. Total terminations are 8. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. It is injected into the electrical part body with 8 pins. On the other hand, analog switches can be constructed using SPST - NC switching circuits. Search with ADG802 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 300mOhm. You can find the functions of the 8 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. The analog switch ic is of the Single supply type and is cost-effective. A low voltage of 1.8V should be applied to the electronic component. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur.
ADG802BRM-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 12MHz
ADG802BRM-REEL7 Applications
There are a lot of Analog Devices Inc. ADG802BRM-REEL7 Analog Switches & Multiplexers ICs applications.
- PDAs
- Modems
- Cable Modem
- Battery Powered Systems
- Private Branch Exchange (PBX)
- Voice over IP/DSL – Integrated Access Devices, Smart
- Data switching
- PBXs
- Isolation
- E1 Network Equipment
