ADG802BRT-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG802 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Throw Configuration | SPST |
| -3db Bandwidth | 12MHz |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Length | 2.9mm |
| RoHS Status | Non-RoHS Compliant |
ADG802BRT-REEL7 Overview
The electrical component comes in SOT-23-6 packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~125°C TA is the extended operating temperature. In total, there are 6 terminations. A high-quality output is provided by the electrical component's 1 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. There are 6 pins injected into the electronic part body. Multiplexers built on a SPST - NC switching circuit are built. Try searching with ADG802 to find analog multiplexer variants. It has an internal resistance of 300mOhm. Datasheets for functions of 6 pins are available. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A low voltage of 1.8V should be applied to the electronic component. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply.
ADG802BRT-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 12MHz
ADG802BRT-REEL7 Applications
There are a lot of Analog Devices Inc. ADG802BRT-REEL7 Analog Switches & Multiplexers ICs applications.
- Cross Connects
- Automatic test equipment
- SONET
- Cable Modem
- Mechanical reed relay replacement
- Transmit
- Access Concentrators
- RGB switches
- DVD-R
- Cell phones
