ADG802BRTZ-500RL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG802 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 12MHz |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 1.3mm |
| Length | 3mm |
| Width | 1.7mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG802BRTZ-500RL7 Overview
As the electronic part is packed in SOT-23-6, international shipping is convenient. The advanced packaging method Tape & Reel (TR) provides high reliability. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~125°C TA extended. In total, there have been 6 terminations. Due to its 1 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. There are 6 pins injected into the electronic part body. Based on SPST - NC switching circuits, these analog multiplexers work. If you are looking for variants of the digital switch, trying search with ADG802. This digital multiplexer has 300mOhm internal resistance. Datasheets for 6 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The digital multiplexer has a low cost Single supply. 1.8V is the lowest voltage that should be fed to the electronic electronic part. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. The transfer of data can be performed over 12MHz bandwidths.
ADG802BRTZ-500RL7 Features
1 Channels
Switch Circuit: SPST - NC
Bandwidth: 12MHz
ADG802BRTZ-500RL7 Applications
There are a lot of Analog Devices Inc. ADG802BRTZ-500RL7 Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- USB 1.1 signal switching circuits
- PBXs
- Automotive applications
- FTTH
- T1/E1 Terminals
- Medical Instrumentation
- Channelized and Unchannelized DS3 applications
- Communication systems
- Data Acquisition Systems
