ADG802BRTZ-REEL
| Parameters | |
|---|---|
| -3db Bandwidth | 12MHz |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG802 |
| Pin Count | 6 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
ADG802BRTZ-REEL Overview
Due to its SOT-23-6 packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. The operating temperature is extended to around -40°C~125°C TA. In total, 6 terminations have occurred. By its 1 channels, the electronic component provides high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 6 series. A SPST - NC switching circuit is used for these analog switches. Try searching for ADG802 variants of the analog switch ic. A 300mOhm internal resistance characterizes this multiplexer. To find out what the functions of 6 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 1.8V. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. If you put voltage higher than 1μA on the digital multiplexer, damage may occur.
ADG802BRTZ-REEL Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 12MHz
ADG802BRTZ-REEL Applications
There are a lot of Analog Devices Inc. ADG802BRTZ-REEL Analog Switches & Multiplexers ICs applications.
- Frame Relay Equipment
- Microprocessor controlled systems
- Automotive applications
- Automatic test equipment
- Routers
- Battery Powered Systems
- Data switching
- Isolation
- Cross Connects
- Data Acquisition Systems
