ADG811YRU
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 14.4μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG811 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 1.8/3.3V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 14.4μW |
| Max Supply Current | 4μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 90MHz |
| On-State Resistance (Max) | 650mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF 35pF |
| On-state Resistance Match-Nom | 0.04Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 25ns, 5ns |
| Charge Injection | 30pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Switch-off Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Normal Position | NC |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG811YRU Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tube is used. A switch device like this is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operational temperature extended around -40°C~125°C TA. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. An 2.5V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 16 series. These analog multiplexers are built based on SPST - NC switching circuits. A total of 4 circuits make up this switch device. Try searching for ADG811 variants of the analog switch ic. An switch multiplexer with 650mOhm internal resistance has a value of 650mOhm. For details about the functions of 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users shouldn't supply more than 3.6V voltage to the switch device. Analogue multiplexer with a Single supply type that is cost-effective. 1.65V is the lowest voltage the electrical component should receive. A voltage of 1.65V~3.6V is required for this switch device, which drains from a single voltage source. Put voltage above 4μA on the multiplexer to cause damage. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
ADG811YRU Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 90MHz
ADG811YRU Applications
There are a lot of Analog Devices Inc. ADG811YRU Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Public switching systems
- Mechanical reed relay replacement
- Low-Voltage
- Imaging
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Communications systems
- Signal routing between systems
- Automotive applications
- Intelligent PBX
