ADG811YRU-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 14.4μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG811 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 1.8/3.3V |
| Number of Channels | 4 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 14.4μW |
| Max Supply Current | 4μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 90MHz |
| On-State Resistance (Max) | 650mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF 35pF |
| On-state Resistance Match-Nom | 0.04Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 25ns, 5ns |
| Charge Injection | 30pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Switch-off Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Normal Position | NC |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG811YRU-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. The total number of terminations is 16. A 4 channel electronic part produces high-quality output. When the electronic component is given a voltage of 2.5V, it should be turned on and run. It is injected into the electrical part body with 16 pins. A SPST - NC switching circuit is used for these analog switches. Use ADG811 to search for variants of the digital switches. Analog switches have 650mOhm internal resistance. Datasheets for functions of 16 pins are available. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 3.6V in normal situations. The digital multiplexer has a low cost Single supply. A low voltage of 1.65V should be applied to the electronic component. The voltage required by this switch device is 1.65V~3.6V, draining from a single voltage supply. Put voltage above 4μA on the multiplexer to cause damage. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
ADG811YRU-REEL7 Features
4 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 90MHz
ADG811YRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG811YRU-REEL7 Analog Switches & Multiplexers ICs applications.
- Cross Connects
- High-Voltage
- Optical Applications
- MP3 players
- Digital access cross connects
- Routers
- Voice over IP/DSL – Integrated Access Devices, Smart
- PDAs
- Avionics test equipment
- Fiber In The Loop (FITL)
