ADG811YRUZ

25ns, 5ns SPST - NC 650mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG811 16 Pins 1nA 2.5V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG811YRUZ
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 822
Description: 25ns, 5ns SPST - NC 650mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG811 16 Pins 1nA 2.5V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 1 month ago)
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Surface Mount	YES
Number of Pins	16
Operating Temperature	-40°C~125°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	650mOhm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	14.4μW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Number of Functions	4
Supply Voltage	2.5V
Base Part Number	ADG811
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	3V
Number of Channels	4
Interface	Parallel
Max Supply Voltage	3.6V
Min Supply Voltage	1.65V
Test Frequency	100kHz
Power Dissipation	14.4μW
Max Supply Current	4μA
Throw Configuration	SPST
Turn On Delay Time	25 ns
Supply Type	Single
Bandwidth	90MHz
Turn-Off Delay Time	5 ns
On-State Resistance (Max)	650mOhm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	67 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	30pF 35pF
On-state Resistance Match-Nom	0.04Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	25ns, 5ns
Insertion Loss (dB)	0.05 dB
Charge Injection	30pC
Channel-to-Channel Matching (ΔRon)	40m Ω
Crosstalk	-90dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	30ns
Switch-off Time-Max	8ns
Voltage - Supply, Single (V+)	1.65V~3.6V
Drain to Source Resistance	500mOhm
Normal Position	NC
Height	1.05mm
Length	5mm
Width	4.4mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG811YRUZ Overview

As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tube is used. Surface Mount is where this multiplexer is located. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~125°C TA. Total terminations are 16. By its 4 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 2.5V voltage supply. An injection of 16 pins is performed into the body of the electrical component. The analog switch ics are built using SPST - NC switching circuits. Try searching for ADG811 variants of the analog switch ic. This digital multiplexer has 650mOhm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 3.6V. Analogue multiplexer with a Single supply type that is cost-effective. 1.65V is the lowest voltage the electrical component should receive. Using a single voltage supply, this switch device consumes 1.65V~3.6V volts. Putting voltage greater than 4μA on the multiplexer may cause damage. This analog switch ic utilizes SEPARATE OUTPUT output. 3V operating voltages can be used with this electrical part. There are 90MHz bandwidths for data transfer. The Drain to Source resistance of this electronic component is 500mOhm.