ADG812YRU
| Parameters | |
|---|---|
| On-state Resistance Match-Nom | 0.04Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 25ns, 5ns |
| Charge Injection | 30pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Switch-off Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 14.4μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG812 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 1.8/3.3V |
| Number of Channels | 4 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 14.4μW |
| Max Supply Current | 4μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 90MHz |
| On-State Resistance (Max) | 650mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF 35pF |
ADG812YRU Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. There are 16 terminations totally. The electronic part delivers high-quality output through its 4 channels. Turning on and running the electrical part should be easy with a 2.5V voltage supply. Into the electrical component body are injected 16 pins. Multiplexers built on a SPST - NO switching circuit are built. Use ADG812 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 650mOhm. Please refer to the datasheets for 16 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 3.6V volts for the multiplexer. Single supply type digital switch with a low cost. 1.65V is the lowest voltage the electrical component should receive. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~3.6V. The switch multiplexer may be damaged if it is exposed to voltage greater than 4μA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
ADG812YRU Features
4 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 90MHz
ADG812YRU Applications
There are a lot of Analog Devices Inc. ADG812YRU Analog Switches & Multiplexers ICs applications.
- Automotive applications
- Automatic test equipment
- SDH
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Avionics
- Fault Tolerant Systems
- Audio/video switches
- PBXs
- Signal routing between systems
- Modems
