ADG812YRU-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 14.4μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG812 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 1.8/3.3V |
| Number of Channels | 4 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 14.4μW |
| Max Supply Current | 4μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 90MHz |
| On-State Resistance (Max) | 650mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF 35pF |
| On-state Resistance Match-Nom | 0.04Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 25ns, 5ns |
| Charge Injection | 30pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Switch-off Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG812YRU-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~125°C TA. In total, there have been 16 terminations. Due to its 4 channels, the electrical component produces high-quality output. A 2.5V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. Unlike digital switches, these are based on SPST - NO switching circuits. ADG812 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 650mOhm. You can find the functions of the 16 pins in the datasheets. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 3.6V voltage to the switch device. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 1.65V as the lowest voltage for the electrical part. This analog switch requires a voltage of 1.65V~3.6V to drain from a single voltage supply. When the digital multiplexer is charged above 4μA, damage can occur. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
ADG812YRU-REEL Features
4 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 90MHz
ADG812YRU-REEL Applications
There are a lot of Analog Devices Inc. ADG812YRU-REEL Analog Switches & Multiplexers ICs applications.
- HDTV
- High speed data transmission line cards
- CSU
- Sample hold systems
- Cell phones
- 65 V DACs
- Communication systems
- Central office
- Microprocessor Controlled Analog Systems
- Video switching
