ADG813YRU
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 14.4μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG813 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 1.8/3.3V |
| Number of Channels | 4 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 14.4μW |
| Max Supply Current | 4μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 90MHz |
| On-State Resistance (Max) | 650mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF 35pF |
| On-state Resistance Match-Nom | 0.04Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 25ns, 5ns |
| Charge Injection | 30pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Switch-off Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG813YRU Overview
This electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. The advanced packaging method Tube provides high reliability. Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~125°C TA. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 4 channels. It is safe to turn on and run the electronic component with a 2.5V voltage supply. A key feature of the 16 series is the inclusion of this electronic part as part of its design. SPST - NO/NC switching circuits are used in these analog switch ics. ADG813 can be used to search for analog multiplexer variants. It has an internal resistance of 650mOhm. The datasheets for the 16 pins explain the functions. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 3.6V should not normally be supplied to the switches. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 1.65V. A voltage of 1.65V~3.6V is required to drain this analog switch from a single voltage supply. A voltage higher than 4μA may cause damage to the switch multiplexer. This analog switch ic utilizes SEPARATE OUTPUT output.
ADG813YRU Features
4 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 90MHz
ADG813YRU Applications
There are a lot of Analog Devices Inc. ADG813YRU Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Medical
- DSUs
- High reliability control systems
- Multi-Line E1 Interface Cards
- Medical Instrumentation
- Sample-and-hold systems
- Channel Banks
- DVD-R
- Relay replacements
