ADG819BRM
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG819 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Nominal Supply Current | 2μA |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 16 ns |
| -3db Bandwidth | 17MHz |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 71 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 80pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -72dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG819BRM Overview
This electronic part is conveniently packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 2:1. Around -40°C~125°C TA is the extended operating temperature. A total of 8 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. There are 8 pins injected into the electronic part body. A SPDT switching circuit is used for these analog switches. ADG819 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 600mOhm. To find out what the functions of 8 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 1.8V. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. If you put voltage higher than 2μA on the digital multiplexer, damage may occur. An output of 2 is provided by the digital multiplexer.
ADG819BRM Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 17MHz
ADG819BRM Applications
There are a lot of Analog Devices Inc. ADG819BRM Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Isolation
- FTTH
- T1/E1 Terminals
- Precision data acquisition
- Public switching systems
- Multi-Line E1 Interface Cards
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Remote Powered Equipment
- Channel Banks
