Parameters |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
600mOhm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG819 |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Power Supplies |
3/5V |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Power Dissipation |
5μW |
Max Supply Current |
2μA |
Turn On Delay Time |
45 ns |
Supply Type |
Single |
Turn-Off Delay Time |
16 ns |
-3db Bandwidth |
17MHz |
On-State Resistance (Max) |
600mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
71 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
80pF |
On-state Resistance Match-Nom |
0.06Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
45ns, 16ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
60m Ω |
Crosstalk |
-72dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
60ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Length |
3mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG819BRM-REEL Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~125°C TA. There are 8 terminations totally. A 1 channel electronic part produces high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the electrical part body. These analog multiplexers are built based on SPDT switching circuits. A total of 1 circuits make up this switch device. Using the ADG819 search parameter, you can discover variants of the switch. An switch multiplexer with 600mOhm internal resistance has a value of 600mOhm. The datasheets for the 8 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Analogue multiplexer with a Single supply type that is cost-effective. A low voltage of 1.8V should be applied to the electronic component. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. A voltage higher than 2μA may cause damage to the switch multiplexer.
ADG819BRM-REEL Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 17MHz
ADG819BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG819BRM-REEL Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Remote wireless modules
- Battery Powered Systems
- ISDN NT1/TA
- Medical
- Medical systems
- New designs requiring multiplexer functions
- DVD-R
- Channel Banks
- Microprocessor Controlled Analog Systems