Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
600mOhm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG819 |
Pin Count |
8 |
Number of Outputs |
2 |
Qualification Status |
Not Qualified |
Polarity |
Non-Inverting |
Power Supplies |
3/5V |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1nA |
Power Dissipation |
5μW |
Max Supply Current |
2μA |
Turn On Delay Time |
45 ns |
Supply Type |
Single |
Bandwidth |
17MHz |
Turn-Off Delay Time |
16 ns |
On-State Resistance (Max) |
600mOhm |
High Level Output Current |
200mA |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
71 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
80pF |
On-state Resistance Match-Nom |
0.06Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
45ns, 16ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
60m Ω |
Crosstalk |
-72dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
60ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Length |
3mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG819BRMZ-REEL7 Overview
Packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. 2:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~125°C TA are extended for operation. A total of 8 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 8 pins. A SPDT switching circuit is used for these analog switches. Search with ADG819 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 600mOhm. To find out what the functions of 8 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 1.8V. It would be sufficient to run this analogue multiplexer with 1nA current. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. A voltage higher than 2μA may cause damage to the switch multiplexer. In 17MHz-bandwidths, data can be transferred. Multiplexer ics with 2 outputs are available.
ADG819BRMZ-REEL7 Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 17MHz
ADG819BRMZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG819BRMZ-REEL7 Analog Switches & Multiplexers ICs applications.
- PBXs
- Video switching
- Voice over IP/DSL – Integrated Access Devices, Smart
- Mechanical reed relay replacement
- Remote Powered Equipment
- High-Voltage
- Data Acquisition Systems
- Relay replacements
- New designs requiring multiplexer functions
- Audio/video switches