ADG819BRT-REEL7
| Parameters | |
|---|---|
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG819 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 17MHz |
| Turn-Off Delay Time | 16 ns |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 71 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 80pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -72dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
ADG819BRT-REEL7 Overview
Shipping overseas is convenient with the electronic component packed in SOT-23-6. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operational temperature extended around -40°C~125°C TA. The total number of terminations is 6. High-quality output is provided by the electronic component's 1 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. This electrical component is included in the 6 series of products. On the other hand, analog switches can be constructed using SPDT switching circuits. Use ADG819 to search for variants of the digital switches. Analog switches have 600mOhm internal resistance. Datasheets for 6 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analog switch ics with Single supply type are cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. For this multiplexer to operate, 1nA current would be sufficient. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. It may damage the digital multiplexer if the voltage is higher than 2μA. There are 17MHz bandwidths for data transfer. The analog switch ics has 2 outputs.
ADG819BRT-REEL7 Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 17MHz
ADG819BRT-REEL7 Applications
There are a lot of Analog Devices Inc. ADG819BRT-REEL7 Analog Switches & Multiplexers ICs applications.
- Routers
- Cell phones
- Precision test equipment
- Cross Connects
- Digital access cross connects
- T1/E1 Terminals
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Multiplexers
- HDTV
- Automatic test equipment
