ADG819BRTZ-500RL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.95mm |
| Base Part Number | ADG819 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Nominal Supply Current | 2μA |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 17MHz |
| Turn-Off Delay Time | 16 ns |
| On-State Resistance (Max) | 600mOhm |
| High Level Output Current | 200mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 71 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 80pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -72dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 600mOhm |
| Height | 1.3mm |
| Length | 3mm |
| Width | 1.7mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG819BRTZ-500RL7 Overview
Due to its SOT-23-6 packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to -40°C~125°C TA. There are 6 terminations totally. High-quality output is provided by the electronic component's 1 channels. A total of 6 pins are injected into the electrical part body. The analog switch ics are built using SPDT switching circuits. Try searching with ADG819 to find analog multiplexer variants. This digital multiplexer has 600mOhm internal resistance. Datasheets for 6 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 1.8V. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. Put voltage above 2μA on the multiplexer to cause damage. There are 17MHz bandwidths for data transfer. Drain to Source resistance for this electronic component is 600mOhm. This digital multiplexer has 2 outputs.
ADG819BRTZ-500RL7 Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 17MHz
Drain-to-Source resistance: 600mOhm
ADG819BRTZ-500RL7 Applications
There are a lot of Analog Devices Inc. ADG819BRTZ-500RL7 Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Battery-powered systems
- Digital Cross-Connects
- MP3 players
- Frame Relay Equipment
- Signal routing between systems
- Fault Tolerant Systems
- New designs requiring multiplexer functions
- PBXs
- SONET
