Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
SOT-23-6 |
Surface Mount |
YES |
Number of Pins |
6 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
ECCN Code |
EAR99 |
Resistance |
600mOhm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.95mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG819 |
Pin Count |
6 |
Number of Outputs |
2 |
Qualification Status |
Not Qualified |
Polarity |
Non-Inverting |
Power Supplies |
3/5V |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1nA |
Power Dissipation |
5μW |
Max Supply Current |
2μA |
Turn On Delay Time |
45 ns |
Supply Type |
Single |
Bandwidth |
17MHz |
Turn-Off Delay Time |
16 ns |
On-State Resistance (Max) |
600mOhm |
High Level Output Current |
200mA |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
71 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
80pF |
On-state Resistance Match-Nom |
0.06Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
45ns, 16ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
60m Ω |
Crosstalk |
-72dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG819BRTZ-REEL7 Overview
As the electronic part is packed in SOT-23-6, international shipping is convenient. High reliability is ensured by the advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~125°C TA are extended for operation. Totally, there are 6 terminations. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. An electrical component of this type can be found in the 6 series. Circuits based on SPDT switching are used to construct these analog switch ics. Try searching for ADG819 variants of the analog switch ic. The internal resistance of this digital multiplexer is 600mOhm. The datasheets for the 6 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 1.8V. In order to operate this switch device, it would need a current of 1nA. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 2μA. This switch operates within the bandwidth of 17MHz. The analog switch ics has 2 outputs.
ADG819BRTZ-REEL7 Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 17MHz
ADG819BRTZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG819BRTZ-REEL7 Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Digital Cross-Connects
- ATM
- PCMCIA cards
- Relay replacements
- Cellular phones
- Data Acquisition Systems
- High speed data transmission line cards
- E1 Multiplexer
- Optical Applications