ADG821BRM
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Terminal Finish | TIN LEAD |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 8 |
| JESD-30 Code | S-PDSO-G8 |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| -3db Bandwidth | 24MHz |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 85pF 98pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 160m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switch-on Time-Max | 67ns |
| Switch-off Time-Max | 18ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
ADG821BRM Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~125°C TA is the extended operating temperature. Totally, there are 8 terminations. A electrical component with 1 channels is capable of high-quality output. A 3.6V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 8 pins. The analog switch ics are built using SPST - NO switching circuits. It consists of 2 circuits. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V.
ADG821BRM Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 24MHz
ADG821BRM Applications
There are a lot of Rochester Electronics, LLC ADG821BRM Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- High-Voltage
- Multi-Line E1 Interface Cards
- Mechanical reed relay replacement
- Signal routing between systems
- Cellular phones
- Frame Relay Equipment
- Data Acquisition Systems
- Routers
