ADG821BRM

45ns, 16ns SPST - NO 600mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG821 8 Pins 250pA 3.6V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG821BRM
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 217
Description: 45ns, 16ns SPST - NO 600mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG821 8 Pins 250pA 3.6V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Surface Mount	YES
Number of Pins	8
Operating Temperature	-40°C~125°C TA
Packaging	Tube
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Resistance	600mOhm
Subcategory	Multiplexer or Switches
Max Power Dissipation	5μW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	235
Number of Functions	2
Supply Voltage	3.6V
Terminal Pitch	0.65mm
Reach Compliance Code	not_compliant
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	ADG821
Pin Count	8
Qualification Status	Not Qualified
Power Supplies	3/5V
Number of Channels	2
Interface	Parallel
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Power Dissipation	5μW
Max Supply Current	2μA
Throw Configuration	SPST
Turn On Delay Time	45 ns
Supply Type	Single
Bandwidth	24MHz
Turn-Off Delay Time	16 ns
On-State Resistance (Max)	600mOhm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	52 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	85pF 98pF
On-state Resistance Match-Nom	0.16Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	45ns, 16ns
Charge Injection	15pC
Channel-to-Channel Matching (ΔRon)	160m Ω
Crosstalk	-82dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	67ns
Voltage - Supply, Single (V+)	1.8V~5.5V
Normal Position	NO
Height Seated (Max)	1.1mm
Length	3mm
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

ADG821BRM Overview

The electrical component comes in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, there have been 8 terminations. This electronic part offers high-quality output due to its 2 channels. When a voltage supply of 3.6V is used, the electronic component should be turned on and run. The electrical component body receives 8 pins. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching with ADG821 if you're looking for variants. In this multiplexer, the internal resistance is 600mOhm. For functions related to 8 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Single supply type digital switch with a low cost. It is recommended to use 1.8V as the lowest voltage for the electrical part. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. If you put voltage higher than 2μA on the digital multiplexer, damage may occur. It is possible to transfer data over a 24MHz-bandwidth.