Parameters |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
600mOhm |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
3.6V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG821 |
Pin Count |
8 |
Power Supplies |
3/5V |
Number of Channels |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Power Dissipation |
5μW |
Max Supply Current |
2μA |
Throw Configuration |
SPST |
Turn On Delay Time |
45 ns |
Supply Type |
Single |
Turn-Off Delay Time |
16 ns |
-3db Bandwidth |
24MHz |
On-State Resistance (Max) |
600mOhm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
52 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
85pF 98pF |
On-state Resistance Match-Nom |
0.16Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
45ns, 16ns |
Charge Injection |
15pC |
Channel-to-Channel Matching (ΔRon) |
160m Ω |
Crosstalk |
-82dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
67ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Normal Position |
NO |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG821BRM-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~125°C TA. 8 terminations have been made so far. This electronic part offers high-quality output due to its 2 channels. If the voltage supply is 3.6V volts, the electrical component should be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching with ADG821 if you're looking for variants. Analog switches have 600mOhm internal resistance. Datasheets for functions of 8 pins are available. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 1.8V. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 2μA.
ADG821BRM-REEL Features
2 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 24MHz
ADG821BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG821BRM-REEL Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Cross Connects
- Audio and video routing
- PBX interfaces
- Avionics and Military Systems
- Routers
- Isolation
- Intelligent PBX
- Audio/video switches
- Medical systems