ADG822BRM
| Parameters | |
|---|---|
| Resistance | 600mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG822 |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 16 ns |
| -3db Bandwidth | 24MHz |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 85pF 98pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 160m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 67ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
ADG822BRM Overview
This electronic part is conveniently packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), making it easy to ship abroad. High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -40°C~125°C TA are extended for operation. There are 8 terminations totally. The electronic part provides high-quality output because it has 2 channels. When the electronic component is given a voltage of 3.6V, it should be turned on and run. This electrical component is included in the 8 series of products. Unlike digital switches, these are based on SPST - NC switching circuits. Search with ADG822 if you are looking for analog multiplexer variants. There is 600mOhm internal resistance in this digital multiplexer. Datasheets for functions of 8 pins are available. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 1.8V. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 2μA.
ADG822BRM Features
2 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 24MHz
ADG822BRM Applications
There are a lot of Analog Devices Inc. ADG822BRM Analog Switches & Multiplexers ICs applications.
- Cellular phones
- Voice over IP/DSL – Integrated Access Devices, Smart
- ATM
- Public switching systems
- Central office
- Fiber In The Loop (FITL)
- SONET
- Channelized and Unchannelized DS3 applications
- High reliability control systems
- T1/E1 Terminals
