ADG822BRM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG822 |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 16 ns |
| -3db Bandwidth | 24MHz |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 85pF 98pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 160m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 67ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG822BRM-REEL Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Temperatures around -40°C~125°C TA are extended for operation. Totally, there are 8 terminations. This electronic part offers high-quality output due to its 2 channels. A 3.6V voltage supply should turn on and run the electronic component. There are 8 pins injected into the electronic part body. The analog switch ics are built using SPST - NC switching circuits. Look for analog switch ic variants by searching with ADG822. An switch multiplexer with 600mOhm internal resistance has a value of 600mOhm. Please refer to the datasheets for 8 pins functions. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. A low voltage of 1.8V should be applied to the electronic component. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. Putting voltage greater than 2μA on the multiplexer may cause damage.
ADG822BRM-REEL Features
2 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 24MHz
ADG822BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG822BRM-REEL Analog Switches & Multiplexers ICs applications.
- Industrial
- Medical systems
- Multi-Line E1 Interface Cards
- MP3 players
- Wireless Local Loop
- Audio and video routing
- Cellular phones
- Precision test equipment
- Power routing
- Avionics
