ADG823BRMZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG823 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 24MHz |
| Turn-Off Delay Time | 16 ns |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 85pF 98pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 160m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG823BRMZ-REEL7 Overview
This electronic part is conveniently packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~125°C TA. 8 terminations have been made so far. The electronic part provides high-quality output because it has 2 channels. An 5V voltage supply should allow the electrical part to be turned on and run. 8 pins are injected to the electronic part body. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. Try searching for ADG823 variants of the analog switch ic. As far as internal resistance is concerned, it has 600mOhm. Datasheets for 8 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 5.5V to a switch device. Single supply type digital switch with a low cost. It is recommended to use 1.8V as the lowest voltage for the electrical part. For this digital switch to work, 1nA current would suffice. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V. The analogue multiplexer may be damaged if voltage is greater than 2μA. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. 24MHz bandwidths enable data to be transferred.
ADG823BRMZ-REEL7 Features
2 Channels
Switch Circuit: SPST - NO/NC
1nA Supply Current
Bandwidth: 24MHz
ADG823BRMZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG823BRMZ-REEL7 Analog Switches & Multiplexers ICs applications.
- ATM
- Isolation
- Routers
- Fault Tolerant Systems
- Data Acquisition Systems
- Sample hold systems
- New designs requiring multiplexer functions
- PDH Multiplexers
- High reliability control systems
- Imaging
