ADG836LYRM-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.6μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG836 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3.6V |
| Power Supplies | 3/3.3V |
| Number of Channels | 2 |
| Interface | Parallel |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Test Frequency | 100kHz |
| Operating Supply Current | 3nA |
| Power Dissipation | 3.6μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 26 ns |
| Supply Type | Single |
| Bandwidth | 57MHz |
| Turn-Off Delay Time | 7 ns |
| On-State Resistance (Max) | 650mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 25pF |
| On-state Resistance Match-Nom | 0.04Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 26ns, 7ns |
| Insertion Loss (dB) | 0.05 dB |
| Charge Injection | 40pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG836LYRM-REEL7 Overview
Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, you'll find this switch device. 2:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~125°C TA. 10 terminations have been made so far. A 2 channel electronic part produces high-quality output. If the voltage supply is 2.7V volts, the electrical component should be turned on and run. There is an electrical component included in the 10 series. Multiplexers built on a SPDT switching circuit are built. Try searching with ADG836 if you're looking for variants. An switch multiplexer with 650mOhm internal resistance has a value of 650mOhm. The datasheets for the 10 pins explain the functions. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 3.6V. Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 1.65V. The switch device would be able to operate with 3nA current. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~3.6V. The analogue multiplexer may be damaged if voltage is greater than 1μA. Operating voltages of 3.6V are compatible with the electrical part. The transfer of data can be performed over 57MHz bandwidths. The analogue multiplexer has 4 outputs.
ADG836LYRM-REEL7 Features
2 Channels
Switch Circuit: SPDT
3nA Supply Current
Bandwidth: 57MHz
ADG836LYRM-REEL7 Applications
There are a lot of Analog Devices Inc. ADG836LYRM-REEL7 Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- Routers
- Fiber to the Home
- Signal routing between systems
- Modems
- RGB switches
- Cable Modem
- Public switching systems
- Video signal routing
- Data switching
