ADG836LYRMZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.6μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG836 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 3.6V |
| Polarity | Non-Inverting |
| Power Supplies | 1.8/3.3V |
| Number of Channels | 2 |
| Interface | Parallel |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Test Frequency | 100kHz |
| Power Dissipation | 3.6μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 26 ns |
| Supply Type | Single |
| Bandwidth | 57MHz |
| Turn-Off Delay Time | 7 ns |
| On-State Resistance (Max) | 650mOhm |
| High Level Output Current | 300mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 25pF |
| On-state Resistance Match-Nom | 0.04Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 26ns, 7ns |
| Insertion Loss (dB) | 0.05 dB |
| Charge Injection | 40pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG836LYRMZ Overview
The electronic component is convenient to ship overseas because it is packed in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). High reliability is provided by advanced packaging method Tube. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 2:1. Operating temperature extended to -40°C~125°C TA. In total, there have been 10 terminations. This electronic part offers high-quality output due to its 2 channels. It is safe to turn on and run the electronic component with a 2.7V voltage supply. A total of 10 pins are injected into the electrical part body. These analog multiplexers are built based on SPDT switching circuits. Try searching for the analog switch ic with ADG836 if you are looking for variants. There is 650mOhm internal resistance in this digital multiplexer. For functions related to 10 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 3.6V. Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 1.65V. A voltage of 1.65V~3.6V is required for this switch device, which drains from a single voltage source. A voltage higher than 1μA may cause damage to the switch multiplexer. There is a voltage range of 3.6V operating voltages for the electrical part. There are various bandwidths available for data transfer. The analog switch ics has 4 outputs.
ADG836LYRMZ Features
2 Channels
Switch Circuit: SPDT
Bandwidth: 57MHz
ADG836LYRMZ Applications
There are a lot of Analog Devices Inc. ADG836LYRMZ Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- E1 Network Equipment
- Industrial control systems
- Audio signal routing
- PBXs
- Multi-Line E1 Interface Cards
- PBX interfaces
- PDH Multiplexers
- SONET
- Cable PC
