banner_page

ADG836YRM

26ns, 7ns SPDT 650mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG836 10 Pins 200pA Typ 1.8V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-ADG836YRM
  • Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
  • Datasheet: PDF
  • Stock: 747
  • Description: 26ns, 7ns SPDT 650mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG836 10 Pins 200pA Typ 1.8V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Details

Tags

Parameters
Mounting Type Surface Mount
Package / Case 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Surface Mount YES
Number of Pins 10
Operating Temperature -40°C~125°C TA
Packaging Tube
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 10
ECCN Code EAR99
Resistance 650mOhm
Terminal Finish Tin/Lead (Sn/Pb)
Subcategory Multiplexer or Switches
Max Power Dissipation 3.6μW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 240
Number of Functions 2
Supply Voltage 1.8V
Terminal Pitch 0.5mm
Reach Compliance Code not_compliant
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number ADG836
Pin Count 10
Number of Outputs 4
Qualification Status Not Qualified
Power Supplies 1.8/3.3V
Number of Channels 2
Interface Parallel
Max Supply Voltage 3.6V
Min Supply Voltage 1.65V
Test Frequency 100kHz
Power Dissipation 3.6μW
Max Supply Current 1μA
Turn On Delay Time 26 ns
Supply Type Single
Bandwidth 57MHz
Turn-Off Delay Time 7 ns
On-State Resistance (Max) 650mOhm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 67 dB
Current - Leakage (IS(off)) (Max) 200pA Typ
Channel Capacitance (CS(off), CD(off)) 25pF
On-state Resistance Match-Nom 0.1Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 26ns, 7ns
Charge Injection 40pC
Channel-to-Channel Matching (ΔRon) 40m Ω
Crosstalk -90dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Switch-off Time-Max 9ns
Voltage - Supply, Single (V+) 1.65V~3.6V
Normal Position NO/NC
Height Seated (Max) 1.1mm
Length 3mm
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead

ADG836YRM Overview


Shipping overseas is convenient due to the electrical component's packing in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). High reliability is provided by advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. 2:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~125°C TA. The total number of terminations is 10. A 2 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 1.8V voltage supply. It is part of the design of the 10 series that this electronic component is included. Multiplexers built on a SPDT switching circuit are built. Look for analog switch ic variants by searching with ADG836. Analog switches have 650mOhm internal resistance. To find out what the 10 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 3.6V. A cost-effective Single supply type analogue multiplexer. 1.65V is the lowest voltage the electrical component should receive. Analogue multiplexers require a 1.65V~3.6V voltage to drain from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. A 57MHz-bandwidth can be used for data transfer. An output of 4 is provided by the digital multiplexer.

ADG836YRM Features


2 Channels
Switch Circuit: SPDT
Bandwidth: 57MHz

ADG836YRM Applications


There are a lot of Analog Devices Inc. ADG836YRM Analog Switches & Multiplexers ICs applications.

  • PBX interfaces
  • Low-Voltage
  • Ultrasound
  • Communication systems
  • Cable Modem
  • Signal routing between systems
  • Battery-powered systems
  • PDAs
  • Mechanical reed relay replacement
  • T1/E1 Terminals

Write a review

Note: HTML is not translated!
    Bad           Good