ADG836YRM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.6μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG836 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Power Supplies | 1.8/3.3V |
| Number of Channels | 2 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 3.6μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 26 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 7 ns |
| -3db Bandwidth | 57MHz |
| On-State Resistance (Max) | 650mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 200pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 25pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 26ns, 7ns |
| Charge Injection | 40pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 9ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG836YRM-REEL Overview
Presented in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~125°C TA extended. Total terminations are 10. By its 2 channels, the electronic component provides high-quality output. In the case of a voltage supply of 1.8V volts, the electrical part can be powered up and run. An electrical component like this is included in the 10 series. The analog switch ics are built using SPDT switching circuits. If you are looking for variants of the digital switch, trying search with ADG836. The internal resistance of this digital multiplexer is 650mOhm. For functions related to 10 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 3.6V. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 1.65V. A voltage of 1.65V~3.6V is required to drain this analog switch from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. There are 4 outputs on the analogue multiplexer.
ADG836YRM-REEL Features
2 Channels
Switch Circuit: SPDT
-3db Bandwidth: 57MHz
ADG836YRM-REEL Applications
There are a lot of Analog Devices Inc. ADG836YRM-REEL Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- Data Acquisition Systems
- Video signal routing
- Avionics test equipment
- SONET/SDH ADM
- Microprocessor controlled systems
- Transmit
- SDH
- Battery Powered Systems
- ISDN NT1/TA
