Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
650mOhm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
3.6μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
1.8V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG836 |
Pin Count |
10 |
Number of Outputs |
4 |
Polarity |
Non-Inverting |
Power Supplies |
1.8/3.3V |
Number of Channels |
2 |
Interface |
Parallel |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.65V |
Test Frequency |
100kHz |
Operating Supply Current |
3nA |
Nominal Supply Current |
4μA |
Power Dissipation |
3.6μW |
Max Supply Current |
1μA |
Turn On Delay Time |
26 ns |
Supply Type |
Single |
Bandwidth |
57MHz |
Turn-Off Delay Time |
7 ns |
On-State Resistance (Max) |
650mOhm |
High Level Output Current |
300mA |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
67 dB |
Current - Leakage (IS(off)) (Max) |
200pA Typ |
Channel Capacitance (CS(off), CD(off)) |
25pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
26ns, 7ns |
Charge Injection |
40pC |
Channel-to-Channel Matching (ΔRon) |
40m Ω |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
9ns |
Voltage - Supply, Single (V+) |
1.65V~3.6V |
Normal Position |
NC |
Height |
850μm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG836YRMZ Overview
The electrical component comes in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tube is used. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operating temperature extended to -40°C~125°C TA. Totally, there are 10 terminations. The electronic part delivers high-quality output through its 2 channels. It is safe to turn on and run the electronic component with a 1.8V voltage supply. An electrical component of this type can be found in the 10 series. These analog multiplexers are built based on SPDT switching circuits. Try searching for the analog switch ic with ADG836 if you are looking for variants. An switch multiplexer with 650mOhm internal resistance has a value of 650mOhm. To find out what the 10 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 3.6V in normal situations. The analog switch ic is of the Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 1.65V. For this multiplexer to operate, 3nA current would be sufficient. Using a single voltage supply, this switch device consumes 1.65V~3.6V volts. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. 57MHz-bandwidths can be used to transfer data between multiplexers. 4 outputs are included in the analogue multiplexer.
ADG836YRMZ Features
2 Channels
Switch Circuit: SPDT
3nA Supply Current
Bandwidth: 57MHz
ADG836YRMZ Applications
There are a lot of Analog Devices Inc. ADG836YRMZ Analog Switches & Multiplexers ICs applications.
- DSUs
- Medical Instrumentation
- Frame Relay Equipment
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- 65 V DACs
- ATM
- ISDN NT1/TA
- Communication systems
- PDAs
- Sample-and-hold systems