Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
650mOhm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
3.6μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
1.8V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG836 |
Pin Count |
10 |
Number of Outputs |
4 |
Qualification Status |
Not Qualified |
Power Supplies |
1.8/3.3V |
Number of Channels |
2 |
Interface |
Parallel |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.65V |
Test Frequency |
100kHz |
Operating Supply Current |
3nA |
Power Dissipation |
3.6μW |
Max Supply Current |
1μA |
Turn On Delay Time |
26 ns |
Supply Type |
Single |
Bandwidth |
57MHz |
Turn-Off Delay Time |
7 ns |
On-State Resistance (Max) |
650mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
67 dB |
Current - Leakage (IS(off)) (Max) |
200pA Typ |
Channel Capacitance (CS(off), CD(off)) |
25pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
26ns, 7ns |
Charge Injection |
40pC |
Channel-to-Channel Matching (ΔRon) |
40m Ω |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
9ns |
Voltage - Supply, Single (V+) |
1.65V~3.6V |
Normal Position |
NC |
Height Seated (Max) |
1.1mm |
Length |
3mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG836YRMZ-REEL Overview
The electronic component is convenient to ship overseas because it is packed in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, there are 10 terminations. Due to its 2 channels, the electrical component produces high-quality output. With a 1.8V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 10 pins. On the other hand, analog switches can be constructed using SPDT switching circuits. Try searching with ADG836 if you're looking for variants. It has an internal resistance of 650mOhm. Datasheets for 10 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 3.6V in normal situations. An effective Single supply digital multiplexer. The lowest voltage the electronic part should receive is 1.65V. This digital switch can be operated with a current of 3nA. A voltage of 1.65V~3.6V is required for this switch device, which drains from a single voltage source. Putting voltage greater than 1μA on the multiplexer may cause damage. The transfer of data can be performed over 57MHz bandwidths. A analog switch ics with 4 outputs is included.
ADG836YRMZ-REEL Features
2 Channels
Switch Circuit: SPDT
3nA Supply Current
Bandwidth: 57MHz
ADG836YRMZ-REEL Applications
There are a lot of Analog Devices Inc. ADG836YRMZ-REEL Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Battery-powered systems
- SONET/SDH ADM
- Isolation
- ATM
- E1 Network Equipment
- USB 1.1 signal switching circuits
- New designs requiring multiplexer functions
- Voice over IP/DSL – Integrated Access Devices, Smart
- Digital Cross-Connects