Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
650mOhm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
3.6μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
1.8V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG836 |
Pin Count |
10 |
Number of Outputs |
4 |
Power Supplies |
1.8/3.3V |
Number of Channels |
2 |
Interface |
Parallel |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.65V |
Test Frequency |
100kHz |
Operating Supply Current |
3nA |
Power Dissipation |
3.6μW |
Max Supply Current |
1μA |
Turn On Delay Time |
26 ns |
Supply Type |
Single |
Bandwidth |
57MHz |
Turn-Off Delay Time |
7 ns |
On-State Resistance (Max) |
650mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
67 dB |
Current - Leakage (IS(off)) (Max) |
200pA Typ |
Channel Capacitance (CS(off), CD(off)) |
25pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
26ns, 7ns |
Charge Injection |
40pC |
Channel-to-Channel Matching (ΔRon) |
40m Ω |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
9ns |
Voltage - Supply, Single (V+) |
1.65V~3.6V |
Normal Position |
NC |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG836YRMZ-REEL7 Overview
The electronic component is convenient to ship overseas because it is packed in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. There is 2:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~125°C TA is the extended operating temperature. In total, there are 10 terminations. Due to its 2 channels, the electrical component produces high-quality output. In the case of a voltage supply of 1.8V volts, the electrical part can be powered up and run. An electrical component like this is included in the 10 series. A SPDT switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with ADG836. A 650mOhm internal resistance characterizes this multiplexer. The datasheets for the 10 pins explain the functions. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 3.6V. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 1.65V. For this multiplexer to operate, 3nA current would be sufficient. A voltage of 1.65V~3.6V is required to drain this analog switch from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. The transfer of data can be performed over 57MHz bandwidths. An output of 4 is provided by the digital multiplexer.
ADG836YRMZ-REEL7 Features
2 Channels
Switch Circuit: SPDT
3nA Supply Current
Bandwidth: 57MHz
ADG836YRMZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG836YRMZ-REEL7 Analog Switches & Multiplexers ICs applications.
- PBXs
- Channelized and Unchannelized DS3 applications
- Sample hold systems
- Cross Connects
- DSLAMs
- Cable Modem
- 65 V DACs
- PDH Multiplexers
- HDTV
- PBX interfaces