Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 4 weeks ago) |
Contact Plating |
Gold |
Mounting Type |
Surface Mount |
Package / Case |
6-TSSOP, SC-88, SOT-363 |
Surface Mount |
YES |
Number of Pins |
6 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
ECCN Code |
EAR99 |
Resistance |
370mOhm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
14.4μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
2.5V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG841 |
Pin Count |
6 |
Operating Supply Voltage |
3.6V |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.65V |
Test Frequency |
100kHz |
Nominal Supply Current |
4μA |
Power Dissipation |
14.4μW |
Max Supply Current |
4μA |
Throw Configuration |
SPST |
Turn On Delay Time |
14 ns |
Supply Type |
Single |
Bandwidth |
21MHz |
Turn-Off Delay Time |
7.8 ns |
On-State Resistance (Max) |
370mOhm |
High Level Output Current |
300mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
54 dB |
Current - Leakage (IS(off)) (Max) |
200pA Typ |
Channel Capacitance (CS(off), CD(off)) |
160pF 160pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
14ns, 7.8ns |
Insertion Loss (dB) |
0.02 dB |
Charge Injection |
200pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
8.2ns |
Voltage - Supply, Single (V+) |
1.65V~3.6V |
Drain to Source Resistance |
370mOhm |
Normal Position |
NO |
Height |
1mm |
Length |
2.2mm |
Width |
1.35mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG841YKSZ-500RL7 Overview
The electronic component is convenient to ship overseas because it is packed in a 6-TSSOP, SC-88, SOT-363. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~125°C TA. Total terminations are 6. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 2.5V voltage supply. 6 pins are injected to the electronic part body. Unlike digital switches, these are based on SPST - NO switching circuits. ADG841 can be used to search for analog multiplexer variants. An switch multiplexer with 370mOhm internal resistance has a value of 370mOhm. The functions of 6 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 3.6V should not normally be supplied to the switches. Analogue multiplexer with a Single supply type that is cost-effective. There should be 1.65V voltage fed to the electrical part below 1.65V. A voltage of 1.65V~3.6V is required for this switch device, which drains from a single voltage source. It may damage the digital multiplexer if the voltage is higher than 4μA. It can operate from 3.6V operating voltages. There are various bandwidths available for data transfer. Drain to Source resistance for this electronic component is 370mOhm.
ADG841YKSZ-500RL7 Features
1 Channels
Switch Circuit: SPST - NO
Bandwidth: 21MHz
Drain-to-Source resistance: 370mOhm
ADG841YKSZ-500RL7 Applications
There are a lot of Analog Devices Inc. ADG841YKSZ-500RL7 Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Automatic test equipment
- Video signal routing
- Cell phones
- MP3 players
- Industrial control systems
- Signal routing between systems
- Residential Gateways, Home Gateway/Router
- Avionics
- FTTH