Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Contact Plating |
Gold |
Mounting Type |
Surface Mount |
Package / Case |
6-TSSOP, SC-88, SOT-363 |
Surface Mount |
YES |
Number of Pins |
6 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
ECCN Code |
EAR99 |
Resistance |
370mOhm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
14.4μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
2.5V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG841 |
Pin Count |
6 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
3.6V |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.65V |
Test Frequency |
100kHz |
Operating Supply Current |
3nA |
Power Dissipation |
14.4μW |
Max Supply Current |
4μA |
Throw Configuration |
SPST |
Turn On Delay Time |
14 ns |
Supply Type |
Single |
Bandwidth |
21MHz |
Turn-Off Delay Time |
7.8 ns |
On-State Resistance (Max) |
370mOhm |
High Level Output Current |
300mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
54 dB |
Current - Leakage (IS(off)) (Max) |
200pA Typ |
Channel Capacitance (CS(off), CD(off)) |
160pF 160pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
14ns, 7.8ns |
Insertion Loss (dB) |
0.02 dB |
Charge Injection |
200pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
8.2ns |
Voltage - Supply, Single (V+) |
1.65V~3.6V |
Drain to Source Resistance |
370mOhm |
Normal Position |
NO |
Length |
2mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG841YKSZ-REEL7 Overview
Packed in 6-TSSOP, SC-88, SOT-363, the electronic component is convenient for shipping overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~125°C TA. In total, 6 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 2.5V, it should be turned on and run. It is part of the design of the 6 series that this electronic component is included. Circuits based on SPST - NO switching are used to construct these analog switch ics. ADG841 can be used to search for analog multiplexer variants. There is 370mOhm internal resistance in this digital multiplexer. For details about the functions of 6 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Users shouldn't supply more than 3.6V voltage to the switch device. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 1.65V. In order to operate this switch device, it would need a current of 3nA. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~3.6V. The analogue multiplexer may be damaged if voltage is greater than 4μA. Operating voltages range from 3.6V. 21MHz bandwidths enable data to be transferred. There is 370mOhm resistance between Drain and Source for this electronic part.
ADG841YKSZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
3nA Supply Current
Bandwidth: 21MHz
Drain-to-Source resistance: 370mOhm
ADG841YKSZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG841YKSZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Digital access cross connects
- Microwave transmission systems
- Audio signal routing
- PBXs
- Communications systems
- E1 Network Equipment
- SONET/SDH ADM
- Low-Voltage
- CSU