ADG884BRMZ-REEL7

50ns, 20ns SPDT 370mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG884 10 Pins 200pA Typ 2.7V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG884BRMZ-REEL7
Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 289
Description: 50ns, 20ns SPDT 370mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG884 10 Pins 200pA Typ 2.7V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 1 month ago)
Contact Plating	Tin
Mounting Type	Surface Mount
Package / Case	10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Surface Mount	YES
Number of Pins	10
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
ECCN Code	EAR99
Resistance	370mOhm
Subcategory	Multiplexer or Switches
Max Power Dissipation	5.5μW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	2.7V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG884
Pin Count	10
Number of Outputs	4
Operating Supply Voltage	5.5V
Polarity	Non-Inverting
Power Supplies	5V
Number of Channels	2
Interface	Parallel
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Test Frequency	100kHz
Analog IC - Other Type	AUDIO/VIDEO SWITCH
Operating Supply Current	3nA
Nominal Supply Current	1μA
Power Dissipation	5.5μW
Max Supply Current	1μA
Turn On Delay Time	50 ns
Supply Type	Single
Bandwidth	18MHz
Turn-Off Delay Time	20 ns
On-State Resistance (Max)	370mOhm
High Level Output Current	400mA
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	200pA Typ
Channel Capacitance (CS(off), CD(off))	103pF
On-state Resistance Match-Nom	0.02Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	50ns, 20ns
Insertion Loss (dB)	0.03 dB
Charge Injection	125pC
Channel-to-Channel Matching (ΔRon)	10m Ω
Crosstalk	-120dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	56ns
Switch-off Time-Max	19ns
Voltage - Supply, Single (V+)	1.8V~5.5V
Normal Position	NC
Height Seated (Max)	1.1mm
Length	3mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG884BRMZ-REEL7 Overview

Shipping overseas is convenient due to the electrical component's packing in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature extended to -40°C~85°C TA. In total, there are 10 terminations. The electronic part delivers high-quality output through its 2 channels. An 2.7V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 10 series of products. Multiplexers built on a SPDT switching circuit are built. ADG884 can be used to search for analog multiplexer variants. An switch multiplexer with 370mOhm internal resistance has a value of 370mOhm. For details about the functions of 10 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 5.5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. 1.8V should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 3nA current would be sufficient. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. A AUDIO/VIDEO SWITCH analog IC is integrated into the board. Operating voltages of 5.5V are compatible with the electrical part. This switch operates within the bandwidth of 18MHz. 4 outputs are included in the analogue multiplexer.