ADG888YRUZ

30ns, 17ns DPDT 480mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG888 16 Pins 200pA Typ 2.7V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG888YRUZ
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 542
Description: 30ns, 17ns DPDT 480mOhm DUAL Analog Switches BREAK-BEFORE-MAKE ADG888 16 Pins 200pA Typ 2.7V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 3 months ago)
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Surface Mount	YES
Number of Pins	16
Operating Temperature	-40°C~125°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	480mOhm
Terminal Finish	MATTE TIN (SN)
Subcategory	Multiplexer or Switches
Max Power Dissipation	20μW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	2.7V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG888
Pin Count	16
Number of Outputs	8
Operating Supply Voltage	5.5V
Power Supplies	3/5V
Number of Channels	2
Interface	Parallel
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Test Frequency	100kHz
Power Dissipation	20μW
Max Supply Current	4μA
Turn On Delay Time	30 ns
Number of Inputs	4
Supply Type	Single
Bandwidth	29MHz
Turn-Off Delay Time	17 ns
On-State Resistance (Max)	480mOhm
Multiplexer/Demultiplexer Circuit	2:2
Off-state Isolation-Nom	67 dB
Current - Leakage (IS(off)) (Max)	200pA Typ
Channel Capacitance (CS(off), CD(off))	58pF
On-state Resistance Match-Nom	0.045Ohm
Switch Circuit	DPDT
Switch Time (Ton, Toff) (Max)	30ns, 17ns
Insertion Loss (dB)	0.03 dB
Charge Injection	70pC
Channel-to-Channel Matching (ΔRon)	40m Ω
Crosstalk	-99dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	50ns
Voltage - Supply, Single (V+)	1.8V~5.5V
Height	1.2mm
Length	5.1mm
Width	4.5mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG888YRUZ Overview

Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 2:2. Operation at a temperature around -40°C~125°C TA. 16 terminations have been made so far. The electronic part delivers high-quality output through its 2 channels. An 2.7V voltage supply should allow the electrical part to be turned on and run. Electronic part bodies are injected with 16 pins. A DPDT switching circuit is used to build these analog multiplexers. Search with ADG888 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 480mOhm. The functions of 16 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 1.8V. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. A voltage higher than 4μA may cause damage to the switch multiplexer. It can operate from 5.5V operating voltages. In order to operate the 4 inputs, there are several steps to follow. 29MHz bandwidths enable data to be transferred. The analog switch ics includes 8 outputs.